 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SX100U &150U 100 & 150 W att, 120 VAC Input Fully Enclosed Switching Power Supply ELECTRICAL SPECIFICATIONS All specifications are typical at nominal input, full load INPUT SPECIFICATIONS Input Voltage.................................................. 85-132 VAC Input Frequency............................................. 50/60 Hz (47-63 Hz) Input Current.................................................. 2.3A / 3.5A (typ) Inrush Current............................................... 14A /15A (typ) OUTPUT SPECIFICATIONS Output Voltage............................................... See chart Output Adjustment......................................... 10% Efficiency........................................................ 82 - 87% Over-Voltage Protection................................. Shutdown 112-150% Output Over-Current Protection................................ Over 105% (Automatic Recovery) Ripple and Noise........................................... 100-200 mVp-p Hold-Up Time................................................. 20 ms Line/Load Regulation..................................... See Chart Rise Time....................................................... 300 ms max. (at 25C nominal output/input) FEATURES REMOTE SENSE OVERVOLTAGE PROTECTION OVERCURRENT PROTECTION HIGHLY RELIABLE CONVECTION COOLED ON/OFF LED LIGHT ADJUSTABLE OUTPUTS 3 YEAR CONTINUOUS USE WARRANTY Leakage Current............................................ 0.5 mA max. GENERAL SPECIFICATIONS MTBF.............................................................>165,000 Hours Isolation Voltage Primary to Secondary.....................AC 2000V Primary to Case..............................AC 1500V Secondary to Case.........................AC 500V Isolation Resistance...................................... Input-Output case 100 M-Ohms min. ENVIRONMENTAL SPECIFICATIONS Operating Temperature .............................. 0C ~ +60C Derates linearly 2.5%/C after 50C Cooling............................................ Convection Temperature Coefficient.................. 0.02%/C Humidity........................................... 20-85% RH (non-condensing) Storage Temperature....................... -20C ~ +85C Shock/Vibration............................... 20G (3 Directions) SAFETIES / EMI FCC-B CISPR-B VCCI-2 PHYSICAL SPECIFICATIONS Metal Enclosed - Terminal Block 50 Series MODEL SX100U-05S SX100U-12S SX100U-15S SX100U-24S OUTPUT VOLTAGE OUTPUT CURRENT EFFICIENCY (TYP) LINE REGULATION LOAD REGULATION 5 VDC 12 VDC 15 VDC 24 VDC 20.0 A 8.6 A 7.0 A 4.4 A 82% 85% 86% 87% 10 mV 10 mV 10 mV 20 mV 20 mV 20 mV 20 mV 30 mV RIPPLE NOISE 100 mVp-p 170 mVp-p 170 mVp-p 200 mVp-p SX100U LED 0.472 V. ADJ. (12) I/O TERMINAL M4 0.748 (19max) 6.299 (160 -1) +S +V 3.661 (93-1) 3.465 (88) 3.248 (82.5) 2-No. 8-32UNC (MOUNTING HOLES) BOTTOM 1.654 1.457 (37) 4.526 (115 -0.5) 1.535 (39 -1) NOTE: *MOUNTING SCREWS NOT TO EXCEED MAX. PENETRATION OF 8mm. *REMOVE SHORT BAR BETWEEN (+5) AND (+V), (-S) AND (0) WHEN USE REMOTE SENSING. *TOLERANCE -1mm. *ALL DIMENSIONS IN INCH (mm) (42) 0.984 (25) 0.709 INCH 0.394 (10) 5.590 (142 -0.5) NOTE: All specifications typical and nominal / full load and 25C unless otherwise noted. Mounting screw lenght should not exceed 0.31 inches or 8 mm. Avoid sustained operation in overload or dead short conditions. Specifications subject to changes without notice. * No. 8-32 mounting holes standard * Dimensions in mm 51 (18) 0 -S FG L N A/C IN H N 2-No. 8-32UNC (MOUNTING HOLES SX100 MODEL SX150U-05S SX150U-12S SX150U-15S SX150U-24S OUTPUT VOLTAGE OUTPUT CURRENT EFFICIENCY (TYP) LINE REGULATION LOAD REGULATION 5 VDC 12 VDC 15 VDC 24 VDC 30.0 A 12.5 A 10.0 A 6.5 A 82% 85% 86% 87% 10 mV 15 mV 15 mV 20 mV 30 mV 45 mV 45 mV 60 mV RIPPLE NOISE 100 mVp-p 170 mVp-p 170 mVp-p 200 mVp-p SX150U NOTE: All specifications typical and nominal / full load and 25C unless otherwise noted. Mounting screw lenght should not exceed 0.31 inches or 8 mm. Avoid sustained operation in overload or dead short conditions. Specifications subject to changes without notice. * No. 8-32 mounting holes standard * Dimensions in mm 52 |
Price & Availability of SX100U-12S
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |